Chemical Resistance Chart

Chemical-resistant, joint-face-adhered, precompressed, primary seal for retrofit and new structural expansion and construction joints where contact with chemicals and chemical dilutions is expected. The polysulfide coating is SynthacalkTM GC2+ and is resistant to the effects of sunlight, rain, snow, ozone, aging, shrinkage, and daily and seasonal cycling changes caused by temperature fluctuation.


This data should only be used as a guide for chemicals at room temperature unless otherwise stated. It is recommended to test the material under actual (or at least simulated) service conditions before specification and/or use.


RECOMMENDED    

Aluminium Sulphate Solution, 50%
Ammonium Chloride Solution, 50%
Ammonium Perchlorate, 15%
Ammonium Perchlorate, 50%
Ammonium Polysulphate
Ammonium Sulphate Solution, 30%
Amyl Alcohol
ASTM Fuel A
ASTM Fuel B
ASTM Fuel C
ASTM Fuel D
Barium Hydroxide, 10%
Borax Solutions, 25%
Boric Acid Solution, 20%
Borohydride Solution
1-4 Butanediol
Butyl Cellosolve
Butyl Dioxitol
Butyl Oxitol
Calcium Chloride Solutions, 50%
Calcium Hydroxide, 20%
Calcium Hypochlorite, 50%
Caustic Potash, 45%
Chlorinated Water, 1ppm
Chlorinated Water, 10ppm
Chlorinated Water, 100ppm
Copper Sulphate Solution, 20%
Cyclohexane
Dibutyl Carbotol
Diethylene Glycol
Ethyl Alcohol
2-Ethyl Hexyl Acrylate
Ethylene Glycol
Ferrous Sulphate, 10%
Fluoboric Acid, 10%
Fuel Oil/Diesel Fuel

Gasoline, Leaded
Gasoline, Unleaded
Gashol
Heptane
Herbicides
— Marksman
— Banvel
— Aatrex 4L
— Prowl 3.3 EC
— Tri-4
— Treflan
— Serve 24E
— Sonalan E.C.

Hexane
Hexane Glycol
Hydrofluoric Acid, 5%
Hydroflouric Acid, 10%
Hydroflouric Acid, 23%
Hydrogen Peroxide, 3%
Hydrogen Peroxide, 20%
Hydrogen Peroxide, 35%
Isobutyl Alcohol
Isobutyl Isobutryate
Isopropyl Alcohol
Isotearic Acid
Jet Fuel (See ASTM Fuels)
Kerosene
Lacquer Solvents
Linseed Oil
Lubricating Oils
Magnesium Chloride Solution, 20%
Magnesium Hydroxide Solution, 30%
Maleic Anhydride, 25% Slurry
Methanol
Methyl Tert-Butyl Ether, 98%
Mineral Spirits

Motor Oil 10W/40
N-Butyl Acrylate
N-Butyl Alcohol
NaphthaVM & P
Naphthalene Oil
Oleic Acid
Oxalic Acid, 20%
Paraffinic Oil
Pesticides
— Arrosolo 3.3E
— Eradicane 6.7E
Phenolic Resins
Phosphoric Acid, 50%
Phthalic Andydride, 38% slurry
Potassium Carbonate
Potassium Hydroxide Solution, 25%
Potassium Hydroxide, 50%
Propylene Glycol
SAE 10 Oil
Shell Tellus Oil 46
Skydrol 500B
Soap Solutions
Sodium Bicarbonate Solution, 25%
Sodium Chloride Solution, 25%
Sodium Hydroxide, 50%
Sodium Hydroxide, 50% @ 120°F
Sodium Sulphide, 25%
Stearic Acid, 20%
Sulfuric Acid, 20%
Texanol
Transmission Fluid
Urea, 10%
Urea Ammonium Nitrate, 32%
Vinyl Acetate
Zinc Chloride, 10%
Zinc Nitrate, 17%


INTERMITTENT CONTACT

   

Acetic Acid, 10%
Acetic Acid, 50%
Acetone
Acrylonitrile
Ammonium Hydroxide Solution, 28%
Carbon Tetrachloride
Ethyl Acetate
Ethyl Acrylate
Ferric Chloride, 50%

Herbicides
— Dual 8E
— Bicep 6L

Hydrochloric Acid, 20%
Isopropylamine
Methyl Acrylate
Methyl Carbitol
Methyl Ethyl Ketone
Methyl Methacrylate

Methyl n-Amyl Ketone
Phosphoric Acid, 60%
Phosphoric Acid, 75%
Sodium Cyanide, 5%
1, 1, 1 Trichloroethane
Triton X100
Vinylidene Chloride
Xylene


NOT RECOMMENDED

   

Acetic Acid, Glacial
Arcosolv PM Acetate
Benzene
Benzoflex 9-88
Benzoic Acid, 5%
Butyl Benzyl Phthalate
Butyl Cellosolve Acetate
Carbon Disulfide
Carbitol Acetate
Cellosolve Acetate
Chromic Acid, 15%
Chromic Acid, 35%
Creosote
Cumene Hydroperoxide
Dimethyl Formanide

Epichlorohydrin
Ethylene Dichloride
Formic Acid, 90%
2-Furaldehyde
Glycol Ether EM
Hydrochloric Acid, 37%
Isophorone, 97%
Malathion 50
2-Mercaptoethanol
Methyl Cellosolve Acetate
Methylene Chloride
Nitric Acid, 10%
Nitric Acid, 30%
Nitric Acid, 60%

Pickling Solution
— 20% Nitric Acid, 4% HF
— 17% Nitric Acid, 4% HF

Potassium Permanganate, 6%
Propylene Oxide
Sodium Hypochlorite, 5%
Sodium Hypochlorite, 8%
Solvent 150
Styrene
Sulfuric Acid, 50%
Sulfuric Acid, 66%
Sulfuric Acid, 8% @ 120°F
Tetrahydrofuran
Tetrahydrofurfuryl Alcohol
Toluene


Back to CHEMSEAL Product Summary
Visit us in store //
5 Airborne Road, Albany,
Auckland
Contact us //     
09 448 1185
info@allco.co.nz

 

MasterSpec 4131AL, 4421AL & 4422AL CETCO is a member of the US Green Building Council BBA References 86/1650 & 95/3099 BRANZ Appraisals 507 (2006) and 647 (2009)
CPD PRESENTATIONS //
Register to have an in-house presentation on the waterproofing solutions we can provide.  
Read more
WARRANTY //
Protect your structure from water ingress with sound design guidance, quality waterproofing products, proper installation and qualified independent inspection
Read more
NEWSLETTERS ONLINE //
Waterproofing Newletters Covering Concrete, Tunnels, Masonry Blockwork, Plaza Decks and MORE
News & information on a range of waterproofing products & applications
Read more
DESIGN ASSISTANCE //
Allco provides a wide range of value-added design assistance service & technical expertise
Read more